Where to Find the 2012 Chevy Cruze Blower Motor Resistor Location

The 2012 Chevy Cruze blower motor resistor is located at the back of the HVAC housing, near the bottom of the firewall. It is accessible from under the dash. The resistor is connected to the blower motor, and it controls the fan speed. Replacing a faulty blower motor resistor will help restore proper fan speed control to your Chevy Cruze. To replace it, you will need to remove the HVAC housing and disconnect the wiring harness from the resistor.

Introduction to 2012 Chevy Cruze Blower Motor Resistor

The Chevy Cruze is a compact car manufactured by General Motors that has been on the market since 2008. This reliable and efficient vehicle has many features that make it a popular choice for drivers. One of these features is the blower motor resistor, which helps regulate the speed of the car’s blower fan. This part is essential for ensuring optimal performance from your HVAC system, allowing you to adjust the fan’s speed as needed.

Where is the Blower Motor Resistor Located in a 2012 Chevy Cruze?

The blower motor resistor in a 2012 Chevy Cruze is located in the passenger side footwell behind the glove box. To access it, you first need to remove the glove box by opening it and pressing down on the two retaining clips on either side of the box. Once these have been released, remove any screws securing the glove box and pull it out of its compartment. The blower motor resistor should then be visible in its mounting bracket, attached to a wiring harness.

Tools Needed to Replace a 2012 Chevy Cruze Blower Motor Resistor

To replace your blower motor resistor in your 2012 Chevy Cruze, you will need:
• Phillips head screwdriver
• Pliers (to remove wiring harness)
• Replacement blower motor resistor
• Torx head screwdriver (to reinstall screws)
• Electrical tape (for insulation)

How to Replace a 2012 Chevy Cruze Blower Motor Resistor

Replacing your blower motor resistor can be done with basic tools and knowledge of automotive repair:

Step-by-Step Guide to Replacing the Resistor:

1. Disconnect negative battery cable from battery terminal and lay aside safely.
2. Remove screws holding glove box in place with Phillips head screwdriver and remove glove box from dashboard area.
3. Locate blower motor resistor behind glove box on passenger side footwell and disconnect wiring harness connected to it using pliers or hands if possible.
4. Remove mounting bracket holding resistor in place with Phillips head screwdriver and discard old unit accordingly.
5. Install new unit in mounting bracket with Phillips head screwdriver or Torx head screwdriver depending on type of screws used by manufacturer, then reattach wiring harness using pliers or hands if possible and secure properly with electrical tape for insulation purposes if necessary.
6. Reinstall glove box into dashboard area using Phillips head screwdriver and secure screws tightly before proceeding further with installation process.
7 Reconnect negative battery cable back onto battery terminal and test newly installed unit by turning on air conditioning system inside cabin interior to ensure functionality before closing hood securely afterwards if applicable..

Troubleshooting Tips for a 2012 Chevy Cruze Blower Motor Resistor

If your newly installed blower motor resistor fails to function properly after following installation instructions carefully, there could be several causes for this issue that are relatively easy to troubleshoot:

• Ensure all connections are secure between wiring harnesses, mounting brackets, etc., as loose connections can cause improper functioning of component parts within air conditioning system overall • Check fuse associated with component part for any signs of damage or corrosion that may be causing an interruption within air conditioning system overall • Check all other component parts within air conditioning system for any signs of damage or corrosion that may be causing an interruption within system overall

Advantages of Replacing a 2012 Chevy Cruze Blower Motor Resistor

Replacing the blower motor resistor on your 2012 Chevy Cruze can bring many benefits. The most important of these is improved air flow in the cabin. A faulty blower motor resistor can cause the fan to blow weakly or not at all, leading to discomfort in the vehicle. Replacing it with a new resistor can restore proper air flow and ensure a comfortable cabin temperature for passengers. Additionally, replacing a faulty blower motor resistor will improve the efficiency of the fan, making it use less energy in order to operate. This can help to save you money on your energy bills and reduce wear and tear on other components like the air conditioning system.

Common Issues with a 2012 Chevy Cruze Blower Motor Resistor

The most common issue with a blower motor resistor in a 2012 Chevy Cruze is that it will fail after extended use due to wear and tear. This could be caused by dirt, dust, or other debris that gets trapped inside the resistor. Additionally, corrosion within the unit could cause it to malfunction as well. When this happens, you will likely experience symptoms such as reduced air flow from the fan or an intermittent blowing of air from one speed setting to another.

Where to Get Replacement Parts for a 2012 Chevy Cruze Blower Motor Resistor

If you need replacement parts for your 2012 Chevy Cruze blower motor resistor, there are many options available online and in stores. You can purchase new resistors directly from auto parts retailers like AutoZone or Advance Auto Parts, or you may be able to find them through online vendors such as Amazon or eBay. Additionally, you may be able to find used resistors at junkyards or salvage yards which could help you save money if you’re on a tight budget.

Frequently Asked Questions about a 2012 Chevy Cruze Blower Motor Resistor

Q: How do I know if my blower motor resistor needs replacing?
A: If your fan is blowing weakly or intermittently from one speed setting to another then it’s likely that your blower motor resistor needs replacing. Additionally, if you notice any strange smells coming from inside your vehicle then this could also indicate a problem with your blower motor resistor and should be checked out by an experienced mechanic as soon as possible.
Q: What tools do I need for replacing my blower motor resistor?
A: You will need basic hand tools such as pliers and screwdrivers in order to complete this job safely and effectively. Additionally, some specialized tools such as an ohmmeter may be required depending on the specific make and model of your vehicle.
Q: How long does it take to replace a blower motor resistor?
A: The time required for this job will vary depending on your experience level but typically takes between 30 minutes and one hour when done correctly using all necessary tools and safety precautions.

Summary of Replacing the 2012 Chevy Cruze Blower Motor Resistor

Replacing the blower motor resistor in your 2012 Chevy Cruze is an easy job that can be completed in just over an hour using basic hand tools such as pliers and screwdrivers along with any specialized tools that may be required depending on make/model specifics of your vehicle.. Doing so brings many advantages including improved air flow in the passenger cabin along with more efficient fan operation which saves energy costs over time. If you’re experiencing any issues with reduced airflow from your fan then consider replacing your blower motor resistor as soon as possible – parts are readily available online or at auto parts stores near you!

FAQ & Answers

Q: What is a blower motor resistor?
A: A blower motor resistor is an electrical component in a vehicle’s heating and air conditioning system that regulates the amount of current flowing to the blower motor. This component is responsible for controlling the speed of the blower fan.

Q: How do I access the blower motor resistor in my 2012 Chevy Cruze?
A: To access the blower motor resistor on a 2012 Chevy Cruze, you will need to remove the glove box, as well as any other components that may be blocking access to it. Once you have done this, you should be able to locate and access the resistor.

Q: What tools do I need to replace a 2012 Chevy Cruze blower motor resistor?
A: In order to replace a 2012 Chevy Cruze blower motor resistor, you will need basic tools such as a flathead screwdriver, needle-nose pliers, and possibly some wire cutters. You may also need some electrical tape or shrink wrap for connecting wires.

Q: What are some common issues with a 2012 Chevy Cruze blower motor resistor?
A: The most common issue with a 2012 Chevy Cruze blower motor resistor is that it can become worn out or damaged over time due to normal usage or exposure to extreme temperatures. This can lead to decreased performance from your vehicle’s heating and air conditioning system. It can also cause excessive noise from the fan when it is running.

Q: Where can I get replacement parts for my 2012 Chevy Cruze blower motor resistor?
A: Replacement parts for your 2012 Chevy Cruze blower motor resistor can be purchased at most auto parts stores or online retailers. You should also be able to find OEM replacement parts from your local Chevrolet dealership if needed.

In conclusion, the 2012 Chevy Cruze blower motor resistor is located under the dashboard on the passenger side of the vehicle. It is necessary to remove some of the trim pieces in order to access and replace it. Having a working knowledge of how to do this can be very helpful in getting the job done quickly and safely.