How to Fix the P0707 Code – A Detailed Guide

AvatarByCarl Frisch

P0707 is a diagnostic trouble code (DTC) for a faulty transmission range sensor. This code is common in vehicles with automatic transmissions and indicates that the transmission is stuck in the wrong gear. The transmission range sensor, also known as the neutral safety switch or manual lever position switch, is responsible for detecting the position of the gear selector and relaying this information to the vehicle’s powertrain control module (PCM). When this code is triggered, it means that the PCM has detected an incorrect signal from the transmission range sensor.

In order to fix this code, it is important to first diagnose the problem correctly. Common causes of this code include a faulty transmission range sensor, incorrect wiring, or damaged wiring connectors. If any of these components are found to be defective, they should be replaced with new parts. Additionally, it may also be necessary to inspect and clean any corroded connectors before reinstalling them onto their respective components. It may also be necessary to reset the ECU after replacing any components in order to clear any stored DTC codes.

Common Causes of P0707 Code

P0707 is a diagnostic trouble code (DTC) for a transaxle range sensor circuit malfunction. It is an issue that affects automatic transmission vehicles and can cause the engine to run poorly or even not at all. It is important to understand the symptoms, reasons, and common repair solutions for this code in order to properly diagnose and resolve the issue.

Symptoms of P0707 Code

The most common symptom of the P0707 code is that the engine will not start or will run rough. Other signs include transmission slipping, delayed shifts, or a check engine light illuminated on the dashboard.

Reasons Behind P0707 Code

A variety of issues can cause the P0707 code to be triggered. These include a faulty transaxle range sensor, wiring issues, or a faulty transmission solenoid. In some cases, low or dirty transmission fluid or a vacuum leak can also be responsible for triggering this code.

Common Repair Solutions for P0707 Code

The first step in resolving this issue is to inspect the transaxle range sensor and its associated wiring and connectors. If there are no visible signs of damage then it may be necessary to test them with an ohmmeter. If any faults are found then it should be replaced as soon as possible. Additionally, if there is any suspicion that a transmission solenoid may be defective then it should also be tested and replaced if necessary.

Troubleshooting Tips for P0707 Code

In addition to inspecting and testing the transaxle range sensor and its associated wiring, it is important to inspect the transmission fluid level and condition. If it is either low or dirty then it should be changed as soon as possible in order to ensure proper operation of the vehicle’s transmission system. Additionally, if there is any suspicion that there may be a vacuum leak present then this should also be investigated as this could lead to further issues with the vehicle’s performance.

Fixing a P0707 Code in an Automobile

If all other troubleshooting steps have been completed without success then it may be necessary to replace either the transaxle range sensor or transmission solenoid in order to resolve the issue causing the code. Depending on which part needs replacing, this task may require professional assistance from an experienced mechanic due to needing special tools for removal/installation of parts inside the vehicle’s transmission system.

Cost of Repairing a P0707 Code in an Automobile

The cost of repairing a P0707 code in an automobile will depend on which parts need replacing and where they are located within your vehicle’s transmission system. Generally speaking, replacing either part should cost between $200-$400 depending on labor costs at your local repair shop plus additional fees for parts and taxes if applicable in your area.

Preventive Measures to Avoid a P0707 Code in an Automobile

The best way to avoid getting a P0707 code in an automobile is by regularly checking the transaxle range sensor and other components related to the transmission system. It’s important to make sure that all of the electrical connections are secure, that there are no signs of corrosion or damage, and that the wiring harness is intact. Additionally, it’s also important to ensure that all fluid levels are topped up and kept at the correct level. If any issues arise with any of these components, then it’s essential for them to be addressed immediately as this will help prevent any further issues from occurring.

Alternatives to Repairing a P0707 Code in an Automobile

If a P0707 code does occur, then there are some alternatives available to repair it without having to replace the entire transmission system. The first option is to reset the transmission range sensor. This can be done by disconnecting the battery for approximately five minutes and then reconnecting it again. Alternatively, replacing the faulty part or parts may be necessary if they are beyond repair or if they need to be upgraded.

Expert Advice on Fixing a P0707 Code in an Automobile

When dealing with a faulty transaxle range sensor, it’s best practice to get expert advice before attempting any repairs yourself as this can help prevent further damage from occurring. Depending on how serious the issue is, you may need to take your vehicle into a certified mechanic or dealership service department who will have access to diagnostic tools and knowledge base that could help determine exactly what needs fixing and also provide advice on how best to go about repairing it.

Pros and Cons of Fixing a P0700 Series Codes in an Automobile

Fixing any type of code in an automobile has its advantages and disadvantages, however when it comes specifically to fixing codes from within the P0700 series, there are some pros and cons that should be considered before proceeding with repairs. On one hand, by fixing these codes you can potentially save money on fuel efficiency as well as improving performance overall; however on the other hand, if not done correctly these repairs can end up costing more than expected due to potential additional damages caused during repair work or money wasted on replacement parts that aren’t actually needed.

Understanding the Impact of Ignoring a P0700 Series Codes in an Automobile

Ignoring codes within the P0700 series can have serious consequences for your vehicle’s overall performance as well as potentially causing costly damages down the line if left unchecked for too long. By ignoring these codes you could end up wasting fuel efficiency due to incorrect readings coming from faulty sensors or components which could result in higher bills at the gas station; additionally you may find yourself needing more expensive repairs than if you had addressed them sooner due to additional wear-and-tear caused by ignoring them. Therefore it’s essential for any codes within this series (or indeed any code) not be ignored but dealt with as soon as possible in order for your vehicle’s performance not suffer unnecessarily nor cause further damage down the line.

FAQ & Answers

Q: What is P0707 Code?
A: P0707 Code is an OBD-II trouble code related to the transmission range sensor circuit malfunction. It is a generic code, which means that it applies to all makes and models of vehicles equipped with an OBD-II system.

Q: What are the Common Causes of P0707 Code?
A: The common causes of P0707 Code include a faulty transaxle range sensor, faulty wiring, or a defective transmission solenoid. Additionally, issues with the transmission fluid or vacuum line may also be to blame.

Q: What are the Symptoms of P0707 Code?
A: The symptoms of P0707 Code include engine misfires, erratic shifting, and delayed shifting. The Check Engine light may also be illuminated on the dashboard.

Q: How Can I Fix a P0707 Code in an Automobile?
A: To fix a P0707 Code in an automobile, you can replace the transaxle range sensor or replace the transmission solenoid. Additionally, you can inspect and adjust the wiring and connectors, as well as check for any vacuum line issues.

Q: How Much Does it Cost to Repair a P0707 Code in an Automobile?
A: The cost to repair a P0707 code in an automobile will depend on several factors such as make and model of your car, labor rates charged by your local mechanic shop, cost of parts needed for the repair etc. Generally speaking, you should expect to pay anywhere between $100-$400 for parts and labor to repair this issue in most cars.

The p0707 code can be a tricky one to diagnose, as it could be caused by a variety of different issues. It is important to have the vehicle properly diagnosed and inspected in order to determine the exact cause and possible fix. Common causes of this code include a faulty transmission range sensor, wiring or connection issues, or a defective transmission shift solenoid. These should all be checked by a qualified technician in order to find the most effective solution.

Author Profile

Carl Frisch
Carl Frisch
With more than 30 years in the bicycle industry, I have a strong background in bicycle retailing, sales, marketing and customer service. I have a passion for cycling and a dedication to excellence. As a manager, I worked diligently to increase my capabilities and responsibilities, managing up to eleven mechanics (at Palo Alto Bicycles) and later as a working partner in my own store.

As the shop owner of Spoke n’ Word Cycles in Socorro, NM, the success of the mission was my responsibility, which I pursued passionately since we opened in 2003 through the spring of 2011. I am adept at managing owned and loan inventory, preparing weekly & annual inventory statements, and managing staff. The role as managing partner also allowed me tremendous freedom. I used this personal freedom to become more deeply involved in my own advancement as a mechanic, to spearhead local trail building, and advocating for cycling both locally and regionally.

As a mechanic, I have several years doing neutral support, experience as a team mechanic, and experience supporting local rides, races, club events. I consistently strive to ensure that bicycles function flawlessly by foreseeing issues and working with the riders, soigners, coaches and other mechanics. Even with decades of experience as a shop mechanic and team mechanic, and continue to pursue greater involvement in this sport as a US Pro Mechanic, and UCI Pro Mechanic.

Similar Posts