Solving the Problem of a Honda Accord Sun Visor That Won’t Stay Up

AvatarByCarl Frisch

The Honda Accord Sun Visor is an important part of the car and helps to protect the driver’s eyes from the sun. Unfortunately, sometimes the sun visor can become loose or won’t stay up. This can be a problem because it limits visibility for the driver and can be dangerous if not addressed. There are several potential causes for this issue, including a broken hinge, a worn out screw, or a weak spring. Fortunately, this is usually an easy fix that can be done at home with a few basic tools. The first step is to inspect the sun visor and check for any signs of damage or wear. If there is no visible damage then check to make sure that all screws and hinges are securely in place. If there is any damage or wear then those parts will need to be replaced. Once all the parts are in place then simply adjust the tension of the spring until it holds the visor in place when raised. After these steps have been completed then your Honda Accord’s sun visor should stay up properly again.

Automobile: Troubleshooting a Honda Accord Sun Visor that Won’t Stay Up

Disconnect the Sun Visor

The first step in troubleshooting a Honda Accord sun visor that won’t stay up is disconnecting the sun visor from its mounting bracket. This can be done by simply pressing down on the tab located on the back of the visor and then pulling it away from the bracket. Once you have removed the sun visor, you can inspect it for any signs of damage or wear and tear, such as cracks or fraying fabric.

Inspect the Mounting Bracket and Gear

The next step is to inspect the mounting bracket and gear to see if they are in good condition. The gear should be free of any signs of wear or damage, such as rust or corrosion. If there are any signs of wear, then it is likely that you will need to replace it with a new one. Additionally, check to make sure that all screws, bolts and other hardware are securely in place on the mounting bracket.

Replace the Gear if Necessary

If you find that your Honda Accord sun visor gear is worn or damaged beyond repair, then you will need to replace it with a new one. This can be done by removing all screws and bolts from the mounting bracket and then carefully removing the old gear. Once this is done, you can install a new gear and reattach all hardware before reattaching your sun visor.

Reattach the Sun Visor

Finally, reattach the sun visor to its mounting bracket by first pressing down on the tab located on its back side and then pushing it up against the bracket until it clicks into place securely. Once this is done, your Honda Accord sun visor should stay up properly without any issues.

Heading 1: Problem Description

The Honda Accord is a popular vehicle that has many different features and functions. One of these features is the sun visor, which is designed to help shield the driver’s eyes from direct sunlight. Unfortunately, many Honda Accord owners have experienced an issue with their sun visor where it will not stay in the up position. This can be a very annoying and distracting problem that needs to be addressed in order for the driver to have a safe and enjoyable experience behind the wheel.

Heading 2: Potential Causes

There are several potential causes for a Honda Accord sun visor not staying in the up position. The most common cause is a damaged gear that has loosened screws or defective wiring harness, which may need to be replaced in order to fix the issue. In some cases, the sun visor itself may need to be replaced if it has become worn or damaged over time.

Heading 3: Tools and Items Required to Fix a Honda Accord Sun Visor That Won’t Stay Up

In order to properly fix a Honda Accord sun visor that won’t stay up, you will need several tools and items. These include a Phillips screwdriver, socket wrench set, and possibly a replacement gear if needed. If you are replacing the sun visor itself, you will also need a new one in order to complete the job correctly. It is important that you have all of these items available before beginning any repair work on your vehicle’s sun visor.

FAQ & Answers

Q: What could be the reason why my Honda Accord sun visor won’t stay up?
A: The reason why your Honda Accord sun visor may not stay up could be due to a broken mounting bracket, signs of wear and tear, a damaged gear, loosened screws, or a defective wiring harness.

Q: What tools do I need to fix my Honda Accord sun visor?
A: You will need a Phillips screwdriver, a socket wrench set, and possibly a replacement gear (if necessary) to fix your Honda Accord sun visor.

Q: How do I go about disconnecting the sun visor?
A: To disconnect the sun visor from your Honda Accord you will need to use your Phillips screwdriver to remove the screws that hold it in place. Then lightly pull the sun visor away from the bracket until it is disconnected.

Q: How can I inspect the mounting bracket and gear?
A: To inspect the mounting bracket and gear on your Honda Accord you will need to remove them from the car. Once removed, check for any signs of damage like worn out teeth or missing parts. If any damage is found you may need to replace them with new parts.

Q: How can I reattach the sun visor after repairs are made?
A: After making repairs to your Honda Accord’s sun visor you can reattach it by placing it back into position on the car’s interior and then using your Phillips screwdriver to secure it in place with screws.

In conclusion, the Honda Accord sun visor not staying up is a common issue that can be easily fixed. The most common cause of this issue is the sun visor clips becoming worn and weak, leading to the visor falling down on its own. Replacing the clips should restore the sun visor to its original working condition. If this does not resolve the issue, then further investigation should be done to identify and repair any other underlying issues.

Author Profile

Carl Frisch
Carl Frisch
With more than 30 years in the bicycle industry, I have a strong background in bicycle retailing, sales, marketing and customer service. I have a passion for cycling and a dedication to excellence. As a manager, I worked diligently to increase my capabilities and responsibilities, managing up to eleven mechanics (at Palo Alto Bicycles) and later as a working partner in my own store.

As the shop owner of Spoke n’ Word Cycles in Socorro, NM, the success of the mission was my responsibility, which I pursued passionately since we opened in 2003 through the spring of 2011. I am adept at managing owned and loan inventory, preparing weekly & annual inventory statements, and managing staff. The role as managing partner also allowed me tremendous freedom. I used this personal freedom to become more deeply involved in my own advancement as a mechanic, to spearhead local trail building, and advocating for cycling both locally and regionally.

As a mechanic, I have several years doing neutral support, experience as a team mechanic, and experience supporting local rides, races, club events. I consistently strive to ensure that bicycles function flawlessly by foreseeing issues and working with the riders, soigners, coaches and other mechanics. Even with decades of experience as a shop mechanic and team mechanic, and continue to pursue greater involvement in this sport as a US Pro Mechanic, and UCI Pro Mechanic.

Similar Posts