2011 Honda Accord Axle Nut Size: How to Find It

AvatarByCarl Frisch

The 2011 Honda Accord utilizes a 22mm axle nut size for the rear wheel axles. This size is used on all four-cylinder and V6 models, as well as the Hybrid model. The axle nut must be tightened to a torque specification of 107 foot-pounds with a torque wrench. Failure to properly tighten the axle nut can lead to loosening of the axle nut, resulting in a loss of vehicle stability and potentially dangerous driving conditions. The use of thread locker compound is recommended when reinstalling the axle nut.

Understanding the Axle Nut Size

The axle nut size of a 2011 Honda Accord is determined by the type of axle that is installed in the vehicle. Depending on the model, the size may vary. The OEM (Original Equipment Manufacturer) size of axle nut for a 2011 Honda Accord is M14-1.5. This is the standard size and is used for most Hondas. However, there are aftermarket parts and components that may require a different size nut which can range from M12-1.25 to M18-1.5 depending on application and model.

Benefits of Installing New Axle Nuts on a 2011 Honda Accord

Replacing an axle nut on a 2011 Honda Accord can provide many benefits including improved performance, increased safety and security of your vehicle, increased resale value, and cost savings in the long run. Replacing an old or worn out axle nut can improve performance as it helps to ensure proper fitment and helps to prevent any potential damage to other components due to excessive wear or looseness of components caused by an old or worn out axle nut. Additionally, replacing an old or worn out axle nut can help to increase safety and security as it helps to ensure that all components are properly secured and functioning correctly which can reduce the risk of an accident due to loose parts or components causing instability while driving. Lastly, replacing an old or worn out axle nut can help to increase resale value as it demonstrates that you have taken care of your vehicle throughout its lifetime and have kept up with regular maintenance procedures such as replacing worn out parts in order to keep your vehicle running efficiently over time.

Tools Needed for Replacing an Axle Nut on a 2011 Honda Accord

When replacing an axle nut on a 2011 Honda Accord there are certain tools that will be needed in order to ensure that it is replaced correctly and securely. These tools include a socket set with wrenches, a torque wrench, and an impact gun if necessary. The socket set will be needed in order to properly remove the old axle nut while also allowing you to install the new one securely. The torque wrench will be used in order to make sure that you have applied enough torque when installing the new axle nut so that it does not become loose over time due to lack of tension or pressure applied during installation. The impact gun may also be necessary depending on how tight or loose the old axle nut is as this tool can provide more force then traditional methods when removing bolts or nuts due to its powerful hammering action when activated repeatedly against the head of bolt or nut being removed/installed.

How To Replace An Axle Nut On A 2011 Honda Accord

When replacing an axle nut on a 2011 Honda Accord there are several steps that should be followed in order ensure proper installation and secure attachment: First step would be removing any existing rust from around bolt head using wire brush before attempting removal; Second step would be using socket set with appropriate size socket wrench for removing existing bolt; Third step would be cleaning threads inside hub with wire brush; Fourth step would be applying thread lock compound before installing new bolt; Fifth step would be using torque wrench for tightening new bolt according to specifications provided by manufacturer; Sixth step would be double checking tightness with feeler gauge if necessary; Last step would be lubricating threads after tightening new bolt with grease gun if necessary for proper operation over time.

Potential Problems When Replacing An Axle Nut On A 2011 Honda Accord

When replacing an axle nut on a 2011 Honda Accord there are several potential problems one might encounter during installation process: Incorrectly installed/torqued nuts could cause issues such as vibration while driving due lack of tension applied or looseness caused by over torquing; Unavailability of parts/components could lead one having difficulty finding correct part needed which could lead delays in repair process until part arrives; Improperly installed/torqued nuts could lead to potential damage other components due excessive wear/looseness caused by improper installation process which could lead costly repairs down road if neglected for extended period time without being addressed correctly first time around..

Check for Proper Fitment Before Installation

When replacing an axle nut on a 2011 Honda Accord, it’s important to check for proper fitment before installation. The axle nut should fit snugly and securely onto the axle. If it is too tight or too loose, it may cause problems with the operation of the vehicle. Additionally, make sure to follow the manufacturer’s instructions for best performance and safety.

Common Issues with the 2011 Honda Accord’s Axles and Nuts

Common issues with the 2011 Honda Accord’s axles and nuts include corrosion or rust, worn out bolts and nuts, and other damage caused by regular wear and tear. Corrosion can cause rusting of the axle components, which can lead to premature failure. Worn out bolts and nuts can also cause excessive play in the axle components, resulting in reduced performance of your vehicle.

How to Diagnose Damage to the 2011 Honda Accord’s Axles and Nuts

When diagnosing damage to your axles and nuts on a 2011 Honda Accord, look for visible damage such as cracks or deformations in the parts. Other signs of damage include unusual sounds during driving or a strange feel while steering that could indicate a wear issue in one or more of the components.

Common Fixes for Issues with the 2011 Honda Accord’s Axles and Nuts

Replacement with OEM parts is one of the most common fixes for issues with a 2011 Honda Accord’s axles and nuts. OEM parts are designed to fit perfectly into your vehicle without any modifications. Greasing or lubricating components is also an important step in ensuring optimal performance from your axles and nuts.

Where to Buy Quality Replacement Parts for the 2011 Honda Accord’s Axles and Nuts

The best place to buy quality replacement parts for your 2011 Honda Accord’s axles and nuts is through OEM dealerships or automotive stores that specialize in these types of parts. OEM dealerships will be able to provide you with exact replacements that are designed specifically for your vehicle model, while automotive stores may have more general parts available that could work as well but may not be an exact fitment.

FAQ & Answers

Q: What is the Axle Nut Size of a 2011 Honda Accord?
A: The OEM Axle Nut Size for a 2011 Honda Accord is 21mm.

Q: What are the Benefits of Installing New Axle Nuts on a 2011 Honda Accord?
A: Installing new axle nuts on a 2011 Honda Accord can provide improved performance, safety and security of the vehicle, increased resale value, and cost savings in the long run.

Q: What Tools are Needed for Replacing an Axle Nut on a 2011 Honda Accord?
A: When replacing an axle nut on a 2011 Honda Accord, you will need socket sets and wrenches, torque wrench, and an impact gun.

Q: What are Common Issues with the 2011 Honda Accord’s Axles and Nuts?
A: Common issues with the 2011 Honda Accord’s axles and nuts include corrosion or rust, worn out bolts and nuts.

Q: Where Can I Buy Quality Replacement Parts for the 2011 Honda Accord’s Axles and Nuts?
A: Quality replacement parts for the 2011 Honda Accord’s axles and nuts can be purchased from OEM dealerships or automotive stores.

In conclusion, the 2011 Honda Accord axle nut size is M12×1.5. This size is common on many cars, and is a great choice for Honda Accord owners looking to replace the axle nut on their vehicle. While it may be difficult to find this exact size, it should be available from any quality auto parts store.

Author Profile

Carl Frisch
Carl Frisch
With more than 30 years in the bicycle industry, I have a strong background in bicycle retailing, sales, marketing and customer service. I have a passion for cycling and a dedication to excellence. As a manager, I worked diligently to increase my capabilities and responsibilities, managing up to eleven mechanics (at Palo Alto Bicycles) and later as a working partner in my own store.

As the shop owner of Spoke n’ Word Cycles in Socorro, NM, the success of the mission was my responsibility, which I pursued passionately since we opened in 2003 through the spring of 2011. I am adept at managing owned and loan inventory, preparing weekly & annual inventory statements, and managing staff. The role as managing partner also allowed me tremendous freedom. I used this personal freedom to become more deeply involved in my own advancement as a mechanic, to spearhead local trail building, and advocating for cycling both locally and regionally.

As a mechanic, I have several years doing neutral support, experience as a team mechanic, and experience supporting local rides, races, club events. I consistently strive to ensure that bicycles function flawlessly by foreseeing issues and working with the riders, soigners, coaches and other mechanics. Even with decades of experience as a shop mechanic and team mechanic, and continue to pursue greater involvement in this sport as a US Pro Mechanic, and UCI Pro Mechanic.

Similar Posts